Saturday, 10 March 2018

Download Latest 100-105 Exam Dumps In Just 24 Hours - Dumps4Download.co.in

Question NO:01

Which of the following must be considered when calculating storage and retention on a Cisco Physical Security MSP server? 

A. Number of cameras, frame rates, camera distances, and record on motion requirements
B. Number of cameras, frame rates, and server locations
C. Number of cameras, frame rates, compression types, and record on motion requirements
D. Number of cameras, camera distances, server locations, and compression types

Answer: C

Question NO:02

When editing a view, which of the following cannot be changed?
A. Camera Tour options
B. Layout options
C. Viewing Pane properties
D. Default Display options


Answer: B





2018 648-238  Exam Braindumps - Cisco 648-238  Exam Questions RealExam


Question NO:03

The branch security manager at a retail bank is asked to create a centralized surveillance solution using Cisco VSM. However, the WAN link between headquarters and some of the branches has limited bandwidth. Using Cisco VSM, flexibility of deployment is broad. Which one of the options below is NOT possible?
A. Deploy a centralized VSM solution using H.264, instead of MJPEG encoding in branches with limited WAN speed
B. Retain camera streams on local branch servers, and only access video from headquarters on demand (such as an event or alarm video)
C. Configure cameras for H.264 encoding and 15 fps, store video locally on a server, then transcode the same video stream to 5 fps before sending it to the headquarters security center
D. Configure dual streaming on each camera-one for high-quality local recording, and the other for streaming to headquarters over WAN
E. Trigger remote viewing of live video stream only when the operator at headquarters requests it through VSOM


Answer: C

Question NO:04

For event integration with a third-party application that supports HTTP triggers, which event type will you most likely use?

A. Device trigger
B. Soft trigger
C. Motion event
D. Third-party trigger


Answer: B





Valid And Updated 648-238 Exam Certifications Dumps Questions - Dumps4Download.co.in

Question NO:05


What is the correct camera and lens setup for the use of IR lighting?
A. Color camera with IR corrected lens
B. A camera with day/night mode and IR corrected lens
C. A camera with day/night mode and varifocal lens
D. Color camera with varifocal lens

Answer: B

Question NO:06

A new VSMS server has been added to VSOM, but the storage capacity says "No Repositories." What should you do in order to resolve this?

A
. Restart VSOM
B. Delete the newly added VSMS server from VSOM, and re-add the server
C. The HDDs are faulty. Replace the HDDs in the newly added media server
D. Configure the Local Repositories setting from the VSMC page of the newly added media server


Answer:D



Question NO:07

In VSM 6.3.2, how can PTZ cameras be controlled?
A. USB joystick only
B. USB mouse only
C. PTZ interface control in VSOM only
D. By a USB joystick, USB mouse, or PTZ control interface in VSOM.


Answer: D



Question NO:08

How should you upgrade the firmware of the Cisco IP cameras deployed in a VSM system?
A. Via the web interface of each camera only
B. Via the VSMC page only
C. Via the web interface of each camera and the VSMC page
D. Via the Batch Admin tool


Answer: B




New 2018 648-238 Actual Test Preparation Solutions For Guaranteed Success




Question NO:09

You are asked to design a Cisco Video Surveillance solution that will record 24 hours a day, in both bright and low light conditions. You decide to use Cisco IP cameras that are capable of day and night modes of operation. Which of the following Cisco IP camera series support day/night
operations?
A. Cisco 2600 Series SD IP cameras only
B. Cisco 2900 Series SD PTZ IP cameras only
C. Cisco 4000 Series HD IP cameras only
D. Cisco 5000 Series HD PTZ IP cameras only
E. Cisco 2600, 2900, 4000, and 5000 Series IP cameras

Answer: E


Question NO:10


Cisco VSM services can be started, stopped, or restarted by using the Linux CLI. How do you stop the Cisco services on the server via the CLI?

A. /etc/init.d/cisco stop
B. /etc/init.d/cisco_all stop
C. cisco stop
D. /usr/init.d/cisco stop


Answer: A





Download 100-105  Exam - Valid 648-238 Question Answers - Dumps4Download.co.in


No comments:

Post a Comment